Cybersecurity in the EU Machinery Regulation, for machine builders and their software teams.
Regulation (EU) 2023/1230 states its cybersecurity requirements as essential health and safety requirements: Annex III point 1.1.9 on protection against corruption and point 1.2.1 on control systems. Here they are quoted, with the Annex IV evidence and the Article 20 presumption of conformity.
Who it applies to
Article 8: “Machinery or related products shall only be made available on the market or put into service if, where properly installed and maintained and used for their intended use or under conditions which can reasonably be foreseen, they meet the essential health and safety requirements set out in Annex III.” Partly completed machinery must meet the relevant Annex III requirements.
The duty sits with the manufacturer. When placing machinery or a related product on the market or putting it into service, manufacturers “shall ensure that it has been designed and constructed in accordance with the essential health and safety requirements set out in Annex III” (Article 10(1)). What counts as machinery, a related product or partly completed machinery is set out on the Machinery Regulation overview.
Annex III point 1.1.9: protection against corruption
Connections, the hardware paths to safety-critical software, that software and its data, and evidence of interventions.
“The machinery or related product shall be designed and constructed so that the connection to it of another device, via any feature of the connected device itself or via any remote device that communicates with the machinery or related product does not lead to a hazardous situation.”
“A hardware component transmitting signal or data, relevant for connection or access to software that is critical for the compliance of the machinery or related product with the relevant essential health and safety requirements shall be designed so that it is adequately protected against accidental or intentional corruption.” The machine shall also “collect evidence of a legitimate or illegitimate intervention in that hardware component”, where relevant for that connection or access.
“Software and data that are critical for the compliance of the machinery or related product with the relevant essential health and safety requirements shall be identified as such and shall be adequately protected against accidental or intentional corruption.” The machine “shall identify the software installed on it that is necessary for it to operate safely, and shall be able to provide that information at all times in an easily accessible form.”
“The machinery or related product shall collect evidence of a legitimate or illegitimate intervention in the software or a modification of the software installed on the machinery or related product or its configuration” (Annex III, point 1.1.9).
Annex III point 1.2.1: safety and reliability of control systems
“Control systems shall be designed and constructed in such a way as to prevent hazardous situations from arising.”
Control systems shall be designed and constructed so that “they can withstand, where appropriate to the circumstances and the risks, the intended operating stresses and intended and unintended external influences, including reasonably foreseeable malicious attempts from third parties leading to a hazardous situation”.
“the limits of the safety functions are to be established as part of the risk assessment performed by the manufacturer”, and no modifications to the settings or rules, including during a learning phase, are allowed where they could lead to hazardous situations.
“the tracing log of the data generated in relation to an intervention and of the versions of safety software uploaded after the machinery or related product has been placed on the market or put into service is enabled for five years after such upload, exclusively to demonstrate the conformity of the machinery or related product with this Annex further to a reasoned request from a competent national authority.”
For control systems “with fully or partially self-evolving behaviour or logic that are designed to operate with varying levels of autonomy”, point 1.2.1 adds three conditions:
- “they shall not cause the machinery or related product to perform actions beyond its defined task and movement space”;
- recording of data “on the safety related decision-making process for software based safety systems ensuring safety function including safety components”, after the product is placed on the market or put into service, is enabled “and that such data is retained for one year after its collection”, for the same exclusive purpose and on the same kind of request;
- “it shall be possible at all times to correct the machinery or related product in order to maintain its inherent safety.”
“For wireless control, a failure of the communication or connection or a faulty connection shall not lead to a hazardous situation” (Annex III, point 1.2.1).
What the technical file must show
Annex IV Part A sets what the documentation for machinery and related products includes at least.
Manufacturers “shall draw up the technical documentation set out in Annex IV, Part A” before placing the product on the market or putting it into service (Article 10(2)). They keep it “for at least 10 years after the machinery or the related product has been placed on the market or put into service” (Article 10(3)). For a security team, these items of Annex IV Part A carry the evidence for points 1.1.9 and 1.2.1:
“the documentation on risk assessment demonstrating the procedure carried out”, including the applicable requirements and “the description of the protective measures implemented to meet each applicable essential health and safety requirement”.
“the source code or programming logic of the safety related software to demonstrate the conformity of the machinery or related product with this Regulation further to a reasoned request from a competent national authority provided that is necessary in order for those authorities to be able to check compliance with the essential health and safety requirements set out in Annex III”.
“if the safety related operations are controlled by sensor data, a description, where appropriate, of the general characteristics, capabilities and limitations of the system, data, development, testing and validation processes used” (Annex IV).
Article 10(3) repeats the condition: the source code or programming logic “shall, upon a reasoned request, be made available to the competent national authorities”, if they need it to check compliance with Annex III. For partly completed machinery, Annex IV Part B point (k) has the same source-code item.
How conformity can be presumed
Article 20 presumes conformity with Annex III on four grounds.
Harmonised standards. A product that conforms to harmonised standards whose references are published in the Official Journal is presumed to conform to the Annex III requirements “covered by those standards or parts thereof” (Article 20(1)). Article 20(6) does the same for common specifications adopted under Article 20(3).
Cybersecurity certification. “Machinery and related products that have been certified or for which a statement of conformity has been issued under a cybersecurity certification scheme adopted in accordance with Regulation (EU) 2019/881 the references of which have been published in the Official Journal of the European Union shall be presumed to be in conformity with the essential health and safety requirements set out in Annex III, sections 1.1.9 and 1.2.1, as regards protection against corruption and safety and reliability of control systems insofar as those requirements are covered by the cybersecurity certificate or statement of conformity or parts thereof” (Article 20(9)). The presumption reaches only as far as the certificate or statement covers those requirements.
High-risk AI systems. Until standards or common specifications are referenced or adopted under Article 20 for them, high-risk AI systems that comply with those under “Articles 40 and, respectively, 41 of Regulation (EU) 2024/1689” are presumed to conform to Annex III as regards high-risk AI systems (Article 20(10)).
Next to the AI Act and the CRA
Besides Article 20(10), Article 8 requires the Commission to adopt delegated acts amending Annex III “by adding health and safety requirements in respect of Artificial Intelligence (AI) systems that are classified as high-risk pursuant to Article 6(1) of Regulation (EU) 2024/1689”, where they are a safety component in a product covered by the Regulation or are themselves such a product. “Those delegated acts shall apply by 2 August 2028.” The AI Act explainer covers that Regulation.
Article 20(9) refers to cybersecurity certification schemes under Regulation (EU) 2019/881. The articles quoted on this page do not set out how the Machinery Regulation and the Cyber Resilience Act apply together, so this page does not either; the CRA explainer covers the Cyber Resilience Act on its own terms.
When it applies
Article 54: “This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union.” “It shall apply from 20 January 2027.” Article 54 then lists articles with other dates; Articles 8, 10 and 20 are not among them, so the Annex III requirements, the technical documentation duty and the presumptions on this page apply from 20 January 2027. The overview has the full list of dates.
Questions machine builders ask
It writes it as safety. Annex III point 1.1.9 requires software and data critical for compliance to be adequately protected against accidental or intentional corruption. Point 1.2.1 requires control systems to withstand, where appropriate to the circumstances and the risks, reasonably foreseeable malicious attempts from third parties leading to a hazardous situation.
Under Annex III point 1.2.1, the tracing log of intervention data and of safety software versions uploaded after the machine is placed on the market or put into service is enabled for five years after the upload. For control systems with self-evolving behaviour or logic designed to operate with varying levels of autonomy, data on the safety related decision-making process of software based safety systems, recorded after placing on the market or putting into service, is retained for one year after collection. Both serve exclusively to demonstrate conformity on a reasoned request from a competent national authority.
Article 54 says the Regulation shall apply from 20 January 2027. Articles 8, 10 and 20 are not among the exceptions Article 54 lists, so they apply from that date.
Ask the Machinery Regulation with the source attached
On the free plan, your own AI client searches law and regulation through Ansvar, one jurisdiction or framework per question, and every answer carries its source.
Ask these to see the quality
Paste one into your agent once Ansvar is connected, and check the point it cites.
Using Ansvar, what does Annex III point 1.1.9 of the EU Machinery Regulation (EU) 2023/1230 require on protection against corruption? Quote the point.Using Ansvar, what does Annex III point 1.2.1 of the EU Machinery Regulation say about malicious attempts from third parties and the tracing log? Quote point 1.2.1.Using Ansvar, when does Article 20(9) of the EU Machinery Regulation presume conformity with Annex III points 1.1.9 and 1.2.1? Quote the paragraph.